Sales

1-800-265-1098

email    sales@lmi.ca


Parts & Service

519-963-2505

email    parts@lmi.ca

High-Performance Mixer

HIGH PERFORMANCE DELIVERS LONG TERM VALUE.

The London® High-Performance Mixer more than lives up to its name—especially when it comes to discharging low-slump concrete.

With its 46-inch drum opening and air-lift hopper, this high efficiency unit charges in just 25 seconds and discharges in only 53 seconds. Which is the kind of performance that saves you time and money on every job job.

Check out the details below on the most productive High Performance mixer money can buy.

  • Specifications:

     

    DRUM

    1/4” spun drumhead

    48” inside reinforcing plate

    3/16” LONDON AR200 wear resistant

    3/16" and 1/4 " LONDON AR200 fins with hard surfaced lips
    Solid wire welded seams
    Solid steel drum track machined inside taper and out square
    46” discharge opening
    Auxiliary surge fins
    16” X 22.5” bolt on oval inspection hatch

    FRONT PEDESTAL

    Fully enclosed Cor Ten “A” incorporating a 15-gallon easy clean hydraulic oil reservoir

    Flared lower front and rear flanges to distribute the load

    REAR PEDESTAL

    Easy to clean with service access to the drum rolls and standard “Knee brace”

    Pedestals constructed of Cor Ten “A” corrosion resistant steel

    Fully welded swivel support integrated through pedestal frame

    TRANSMISSION

    Model ZF PK7500 right angle/planetary direct drive

    138.6:1 reduction
    53,104 ft.lb. output torque capacity
    Mounted to machined drum flange by 24 grade 8 bolts and to machined pedestal deck pads by six grade 8 bolts

    HYDROSTATIC

    Eaton heavy-duty variable displacement piston pump with built in 5500 psi relief valve
    Eaton heavy duty motor
    Speed and direction of the drum rotation controlled from the cab and on the rear pendant
    10 micron suction filter
    Heavy-duty front mounted oil cooler with guard

    Water System

    Wide range of sizes, side mounted water tank
    Three position fill, dump and hold valve
    High pressure relief valve
    Pressure regulating valve
    Offset sight gage
    4” diameter spring loaded flapper valve
    1” rear water injection line
    25 foot washdown hose with pistol grip spray nozzle
    Blow out and drain provision for winter operation

    DRUM ROLLERS

    CM1035 alloy steel drum roller

    Tapered roller bearings
    Doublesealed
    Centre shaft lubrication

    Roller surfaced hardened to Rockwell C46

    Full width rear drum roll guard

    CHARGE HOPPER

    38” X 30” top opening

    19” minimum throat dimension

    REAR LADDER

    Non skid ladder rungs and platform base

    Fold down ladder extension
    Ladder rungs align for safety when folded
    Double guard rail on extra large top platform

    CONTROLS

    Electro-hydraulic mix-discharge control in cab and at rear of mixer on 20-foot quick disconnect cable

    Air operated truck engine throttle at rear of mixer (switch for electronic engines)

    Chute raise and lower hydraulic control valve at rear of mixer

    CHUTES

    Paving type main chute with safety hand grabs and hinged fold over with lock

    Two 48” extension chutes for 16 feet total length

    Positive seven position pinlock with 7/8” replaceable hole plate

    CHUTE HOIST

    2 1/2” double acting hydraulic cylinder, 3000 p.s.i. rated

    A-pad gear pump mounted on the Eaton hydrostatic pump

    manual control valve located at the rear of mixer with integral relief and flow regulating valve

    FENDERS

    14 ga. heavy-duty roll formed with stainless steel hardware and rubber washers

    Full tandem length with powder coated Cor Ten “A” centre and end support

    Mud flaps front and rear

    LIGHTS

    Trucklite brand clearance, marker and identification lamps with integral reflectors in accordance with FMVSS

    Trucklite sealed junction box and armour shielded wiring harness

    Midship light is combination clearance/ signal

    PAINT

    Mixer and components shot blasted prior to prime painting

    All components painted prior to assembly

    Top coat one color Sherwin-William 2-part polyurethane

    Tie down angles, fender mounting brackets and water tank cradles are powder coated black

    Water tank straps are black plastic dipped

    SAFETY

    Full complement of bilingual safety decals

    Back up alarm supplied

More in this category: « Trailer Mixer