High-Performance Mixer
HIGH PERFORMANCE DELIVERS LONG TERM VALUE.
The London® High-Performance Mixer more than lives up to its name—especially when it comes to discharging low-slump concrete.
With its 46-inch drum opening and air-lift hopper, this high efficiency unit charges in just 25 seconds and discharges in only 53 seconds. Which is the kind of performance that saves you time and money on every job job.
Check out the details below on the most productive High Performance mixer money can buy.
Specifications:
DRUM
1/4” spun drumhead |
48” inside reinforcing plate |
3/16” LONDON AR200 wear resistant |
3/16″ and 1/4 ” LONDON AR200 fins with hard surfaced lips |
Solid wire welded seams |
Solid steel drum track machined inside taper and out square |
46” discharge opening |
Auxiliary surge fins |
16” X 22.5” bolt on oval inspection hatch |
FRONT PEDESTAL
Fully enclosed Cor Ten “A” incorporating a 15-gallon easy clean hydraulic oil reservoir |
Flared lower front and rear flanges to distribute the load |
REAR PEDESTAL
Easy to clean with service access to the drum rolls and standard “Knee brace” |
Pedestals constructed of Cor Ten “A” corrosion resistant steel |
Fully welded swivel support integrated through pedestal frame |
TRANSMISSION
Model ZF PK7500 right angle/planetary direct drive |
138.6:1 reduction |
53,104 ft.lb. output torque capacity |
Mounted to machined drum flange by 24 grade 8 bolts and to machined pedestal deck pads by six grade 8 bolts |
HYDROSTATIC
Eaton heavy-duty variable displacement piston pump with built in 5500 psi relief valve |
Eaton heavy duty motor |
Speed and direction of the drum rotation controlled from the cab and on the rear pendant |
10 micron suction filter |
Heavy-duty front mounted oil cooler with guard |
WATER SYSTEM
Wide range of sizes, side mounted water tank |
Three position fill, dump and hold valve |
High pressure relief valve |
Pressure regulating valve |
Offset sight gage |
4” diameter spring loaded flapper valve |
1” rear water injection line |
25 foot washdown hose with pistol grip spray nozzle |
Blow out and drain provision for winter operation |
DRUM ROLLERS
CM1035 alloy steel drum roller |
Tapered roller bearings |
Doublesealed |
Centre shaft lubrication |
Roller surfaced hardened to Rockwell C46 |
Full width rear drum roll guard |
CHARGE HOPPER
38” X 30” top opening |
19” minimum throat dimension |
REAR LADDER
Non skid ladder rungs and platform base |
Fold down ladder extension |
Ladder rungs align for safety when folded |
Double guard rail on extra large top platform |
CONTROLS
Electro-hydraulic mix-discharge control in cab and at rear of mixer on 20-foot quick disconnect cable |
Air operated truck engine throttle at rear of mixer (switch for electronic engines) |
Chute raise and lower hydraulic control valve at rear of mixer |
CHUTES
Paving type main chute with safety hand grabs and hinged fold over with lock |
Two 48” extension chutes for 16 feet total length |
Positive seven position pinlock with 7/8” replaceable hole plate |
CHUTE HOIST
2 1/2” double acting hydraulic cylinder, 3000 p.s.i. rated |
A-pad gear pump mounted on the Eaton hydrostatic pump |
manual control valve located at the rear of mixer with integral relief and flow regulating valve |
FENDERS
14 ga. heavy-duty roll formed with stainless steel hardware and rubber washers |
Full tandem length with powder coated Cor Ten “A” centre and end support |
Mud flaps front and rear |
LIGHTS
Trucklite brand clearance, marker and identification lamps with integral reflectors in accordance with FMVSS |
Trucklite sealed junction box and armour shielded wiring harness |
Midship light is combination clearance/ signal |
PAINT
Mixer and components shot blasted prior to prime painting |
All components painted prior to assembly |
Top coat one color Sherwin-William 2-part polyurethane |
Tie down angles, fender mounting brackets and water tank cradles are powder coated black |
Water tank straps are black plastic dipped |
SAFETY
Full complement of bilingual safety decals |
Back up alarm supplied |