High-Performance Mixer
-
High-Performance Mixer High-Performance Mixer
-
High-Performance Mixer High-Performance Mixer
-
High-Performance Mixer High-Performance Mixer
-
High-Performance Mixer High-Performance Mixer
-
High-Performance Mixer High-Performance Mixer
-
High-Performance Mixer High-Performance Mixer
-
Vacuum Gauge Vacuum Gauge
https://lmi.ca/index.php?option=com_k2&view=item&layout=item&id=91&Itemid=164#sigProGalleriac80263a7f2
HIGH PERFORMANCE DELIVERS LONG TERM VALUE.
The London® High-Performance Mixer more than lives up to its name—especially when it comes to discharging low-slump concrete.
With its 46-inch drum opening and air-lift hopper, this high efficiency unit charges in just 25 seconds and discharges in only 53 seconds. Which is the kind of performance that saves you time and money on every job job.
Check out the details below on the most productive High Performance mixer money can buy.
-
Specifications:
DRUM
1/4” spun drumhead
48” inside reinforcing plate
3/16” LONDON AR200 wear resistant
3/16" and 1/4 " LONDON AR200 fins with hard surfaced lips Solid wire welded seams Solid steel drum track machined inside taper and out square 46” discharge opening Auxiliary surge fins 16” X 22.5” bolt on oval inspection hatch FRONT PEDESTAL
Fully enclosed Cor Ten “A” incorporating a 15-gallon easy clean hydraulic oil reservoir
Flared lower front and rear flanges to distribute the load
REAR PEDESTAL
Easy to clean with service access to the drum rolls and standard “Knee brace”
Pedestals constructed of Cor Ten “A” corrosion resistant steel
Fully welded swivel support integrated through pedestal frame
TRANSMISSION
Model ZF PK7500 right angle/planetary direct drive
138.6:1 reduction 53,104 ft.lb. output torque capacity Mounted to machined drum flange by 24 grade 8 bolts and to machined pedestal deck pads by six grade 8 bolts HYDROSTATIC
Eaton heavy-duty variable displacement piston pump with built in 5500 psi relief valve Eaton heavy duty motor Speed and direction of the drum rotation controlled from the cab and on the rear pendant 10 micron suction filter Heavy-duty front mounted oil cooler with guard Water System
Wide range of sizes, side mounted water tank Three position fill, dump and hold valve High pressure relief valve Pressure regulating valve Offset sight gage 4” diameter spring loaded flapper valve 1” rear water injection line 25 foot washdown hose with pistol grip spray nozzle Blow out and drain provision for winter operation DRUM ROLLERS
CM1035 alloy steel drum roller
Tapered roller bearings Doublesealed Centre shaft lubrication Roller surfaced hardened to Rockwell C46
Full width rear drum roll guard
CHARGE HOPPER
38” X 30” top opening
19” minimum throat dimension REAR LADDER
Non skid ladder rungs and platform base
Fold down ladder extension Ladder rungs align for safety when folded Double guard rail on extra large top platform CONTROLS
Electro-hydraulic mix-discharge control in cab and at rear of mixer on 20-foot quick disconnect cable
Air operated truck engine throttle at rear of mixer (switch for electronic engines)
Chute raise and lower hydraulic control valve at rear of mixer
CHUTES
Paving type main chute with safety hand grabs and hinged fold over with lock
Two 48” extension chutes for 16 feet total length
Positive seven position pinlock with 7/8” replaceable hole plate
CHUTE HOIST
2 1/2” double acting hydraulic cylinder, 3000 p.s.i. rated
A-pad gear pump mounted on the Eaton hydrostatic pump
manual control valve located at the rear of mixer with integral relief and flow regulating valve
FENDERS
14 ga. heavy-duty roll formed with stainless steel hardware and rubber washers
Full tandem length with powder coated Cor Ten “A” centre and end support
Mud flaps front and rear
LIGHTS
Trucklite brand clearance, marker and identification lamps with integral reflectors in accordance with FMVSS Trucklite sealed junction box and armour shielded wiring harness
Midship light is combination clearance/ signal
PAINT
Mixer and components shot blasted prior to prime painting
All components painted prior to assembly
Top coat one color Sherwin-William 2-part polyurethane
Tie down angles, fender mounting brackets and water tank cradles are powder coated black
Water tank straps are black plastic dipped
SAFETY
Full complement of bilingual safety decals
Back up alarm supplied